好看的小说完本推荐,女人书籍排行榜

Product description of strain type pressure transmitter:

重傳感器放大器/接線盒(Weight sensor amplifier / junction box)

1、單路普通型變送器(Single channel ordinary transmitter)

變送器將傳感器輸出的mV信號進行精密放大，將力學量轉換成標準電流、電壓信號。
The transmitter accurately amplifies the MV signal output by the sensor and converts the mechanical quantity into standard current and voltage signals.
1.體積小，重量輕具有較高的性價比
Small size, light weight and high cost performance
2.電源浪涌防護，輸入反接保護
Power surge protection and input reverse connection protection
3.多種輸出形式可供選擇，滿足不同用戶需求
A variety of output forms are available to meet the needs of different users
4.接線使用航空插座 5.外殼帶安裝孔，方便用戶的安裝
Use aviation socket for wiring 5 The shell is equipped with mounting holes to facilitate the installation of users

多路普通型變送器(Multi channel ordinary transmitter)

1.除具有普通變送器的特點，還可以降低變頻器等產生的諧波干擾。
In addition to the characteristics of ordinary transmitter, it can also reduce the harmonic interference generated by frequency converter.
2.良好的電磁耐受性（EMS）。
Good electromagnetic tolerance (EMS).

不銹鋼接線盒(Stainless steel junction box)

1.尺寸（四路）：185x134x35（mm）
Size (four-way): 185x134x35 (mm)
2.可選四路、六路、八路等接入方式
4-way and 8-way access modes are optional
3.不銹鋼外殼，美觀耐用，專用密封接頭，密封性好
Stainless steel shell, beautiful and durable, special sealing joint, good sealing performance
4.采用高精度、低漂移電阻和電位器，保證系統工作精度和穩定性
High precision, low drift resistance and potentiometer are adopted to ensure the working accuracy and stability of the system
5.PCB板焊有防浪涌及防感應雷的保護性元器件，可有效防止感應雷和浪涌信號對傳感器及儀表的
The PCB board is welded with protective components against surge and induced lightning, which can effectively prevent the impact of induced lightning and surge signals on sensors and instruments

數字式測控變送器(Digital measurement and control transmitter)

1.采用精密壓鑄鋁外殼，表面噴塑處理。
It adopts precision die-casting aluminum shell with plastic spraying treatment on the surface.
2.適用于精度等級較高及環境較差的場合使用。
It is suitable for occasions with high accuracy and poor environment.
3.采樣頻率：10Hz；具有RS232或RS485通訊功能。
Sampling frequency: 10Hz; It has RS232 or RS485 communication function.
4.兩路繼電器輸出（常開和常閉均提供）。
Two relay outputs (both normally open and normally closed).
5.使用蜂鳴器和發光二極管實現聲報警、光提示。
Use buzzer and led to realize audible alarm and optical prompt.
6.采取抗干擾電源設計技術；電壓模擬量輸出具有短路保護功能。
Adopt anti-interference power supply design technology; The voltage analog output has the function of short-circuit protection.
7.接線使用接線端子及航空插座，外殼帶安裝孔。
Wiring terminals and aviation sockets are used for wiring, and the shell is equipped with mounting holes.
8.使用兩個按鍵進行輸出調整，無電位器等模擬調節部件。
Use two keys to adjust the output without analog adjustment components such as potentiometer.
9.可選配軟件進行標定和報警值設定。
Optional software can be used for calibration and alarm value setting.

軌道式多路數字變送器(Track type multi-channel digital transmitter)

1、變送器可選配一到四路傳感器。
The transmitter can be equipped with one to four sensors.
2、精度：可達0.05%F?S（一拖四）。
Accuracy: up to 0.05% f? S (one for four).
3、采樣頻率： 10次/秒。
Sampling frequency: 10 times / second.
4、通訊口： RS-485，支持標準Modbus RTU通訊協議。
Communication port: RS-485, supporting standard Modbus RTU communication protocol.
5、模擬量輸出：4-20mA或0-5V/10V。
Analog output: 4-20mA or 0-5V / 10V.
6、傳感器激勵電壓：5VDC。
Sensor excitation voltage: 5VDC.
7、模塊工作電源：12~36VDC。
Working power supply of the module: 12 ~ 36VDC.
8、具有總線供電及RS-485通信功能。
It has bus power supply and RS-485 communication function.
9、標準DIN導軌安裝方式。
Standard DIN rail installation.
10、殼體尺寸（帶接線端子）：115mm×90mm×40mm。
Shell size (with terminal): 115mm × 90mm × 40mm。
11、工作溫度 -20～70℃。
Working temperature: - 20 ~ 70 ℃.
12、采用抗干擾電源設計。
Anti interference power supply design is adopted.
13、使用兩個按鍵進行輸出調整，無電位器等模擬調節器件。
Two keys are used for output adjustment, without analog adjustment devices such as potentiometers.
14、防護等級IP65。
Protection grade IP65.

Application fields:

Product family:

Specification parameter

重傳感器放大器/接線盒(Weight sensor amplifier / junction box)

1、單路普通型變送器(Single channel ordinary transmitter)

變送器將傳感器輸出的mV信號進行精密放大，將力學量轉換成標準電流、電壓信號。
The transmitter accurately amplifies the MV signal output by the sensor and converts the mechanical quantity into standard current and voltage signals.
1.體積小，重量輕具有較高的性價比
Small size, light weight and high cost performance
2.電源浪涌防護，輸入反接保護
Power surge protection and input reverse connection protection
3.多種輸出形式可供選擇，滿足不同用戶需求
A variety of output forms are available to meet the needs of different users
4.接線使用航空插座 5.外殼帶安裝孔，方便用戶的安裝
Use aviation socket for wiring 5 The shell is equipped with mounting holes to facilitate the installation of users

多路普通型變送器(Multi channel ordinary transmitter)

1.除具有普通變送器的特點，還可以降低變頻器等產生的諧波干擾。
In addition to the characteristics of ordinary transmitter, it can also reduce the harmonic interference generated by frequency converter.
2.良好的電磁耐受性（EMS）。
Good electromagnetic tolerance (EMS).

不銹鋼接線盒(Stainless steel junction box)

1.尺寸（四路）：185x134x35（mm）
Size (four-way): 185x134x35 (mm)
2.可選四路、六路、八路等接入方式
4-way and 8-way access modes are optional
3.不銹鋼外殼，美觀耐用，專用密封接頭，密封性好
Stainless steel shell, beautiful and durable, special sealing joint, good sealing performance
4.采用高精度、低漂移電阻和電位器，保證系統工作精度和穩定性
High precision, low drift resistance and potentiometer are adopted to ensure the working accuracy and stability of the system
5.PCB板焊有防浪涌及防感應雷的保護性元器件，可有效防止感應雷和浪涌信號對傳感器及儀表的
The PCB board is welded with protective components against surge and induced lightning, which can effectively prevent the impact of induced lightning and surge signals on sensors and instruments

數字式測控變送器(Digital measurement and control transmitter)

1.采用精密壓鑄鋁外殼，表面噴塑處理。
It adopts precision die-casting aluminum shell with plastic spraying treatment on the surface.
2.適用于精度等級較高及環境較差的場合使用。
It is suitable for occasions with high accuracy and poor environment.
3.采樣頻率：10Hz；具有RS232或RS485通訊功能。
Sampling frequency: 10Hz; It has RS232 or RS485 communication function.
4.兩路繼電器輸出（常開和常閉均提供）。
Two relay outputs (both normally open and normally closed).
5.使用蜂鳴器和發光二極管實現聲報警、光提示。
Use buzzer and led to realize audible alarm and optical prompt.
6.采取抗干擾電源設計技術；電壓模擬量輸出具有短路保護功能。
Adopt anti-interference power supply design technology; The voltage analog output has the function of short-circuit protection.
7.接線使用接線端子及航空插座，外殼帶安裝孔。
Wiring terminals and aviation sockets are used for wiring, and the shell is equipped with mounting holes.
8.使用兩個按鍵進行輸出調整，無電位器等模擬調節部件。
Use two keys to adjust the output without analog adjustment components such as potentiometer.
9.可選配軟件進行標定和報警值設定。
Optional software can be used for calibration and alarm value setting.

軌道式多路數字變送器(Track type multi-channel digital transmitter)

1、變送器可選配一到四路傳感器。
The transmitter can be equipped with one to four sensors.
2、精度：可達0.05%F?S（一拖四）。
Accuracy: up to 0.05% f? S (one for four).
3、采樣頻率： 10次/秒。
Sampling frequency: 10 times / second.
4、通訊口： RS-485，支持標準Modbus RTU通訊協議。
Communication port: RS-485, supporting standard Modbus RTU communication protocol.
5、模擬量輸出：4-20mA或0-5V/10V。
Analog output: 4-20mA or 0-5V / 10V.
6、傳感器激勵電壓：5VDC。
Sensor excitation voltage: 5VDC.
7、模塊工作電源：12~36VDC。
Working power supply of the module: 12 ~ 36VDC.
8、具有總線供電及RS-485通信功能。
It has bus power supply and RS-485 communication function.
9、標準DIN導軌安裝方式。
Standard DIN rail installation.
10、殼體尺寸（帶接線端子）：115mm×90mm×40mm。
Shell size (with terminal): 115mm × 90mm × 40mm。
11、工作溫度 -20～70℃。
Working temperature: - 20 ~ 70 ℃.
12、采用抗干擾電源設計。
Anti interference power supply design is adopted.
13、使用兩個按鍵進行輸出調整，無電位器等模擬調節器件。
Two keys are used for output adjustment, without analog adjustment devices such as potentiometers.
14、防護等級IP65。
Protection grade IP65.

Ordering considerations

How to select load cell

Weighing sensor is known as the heart of electronic weighing instrument. Its performance determines the accuracy and stability of electronic weighing instrument to a great extent. When designing electronic weighing apparatus, we often encounter the problem of how to select sensors.
The load cell is actually a device that converts the mass signal into measurable electrical signal output. The actual working environment of the sensor should be considered before using the sensor, which is very important for the correct selection of the sensor. It is related to whether the sensor can work normally, its safety and service life, and even the reliability and safety of the whole weighing instrument.

The impact of the environment on the sensor mainly includes the following aspects:
(1) The high temperature environment causes some problems to the sensor, such as melting of coating materials, civilized solder joints, structural changes of stress in the elastomer and so on. For sensors working in high temperature environment, high temperature resistant sensors are often used; In addition, heat insulation, water cooling or air cooling devices must be added.
(2) The influence of dust and humidity on the short circuit of the sensor. Under such environmental conditions, sensors with high tightness shall be selected. Different sensors have different sealing methods, and their tightness is very different.
Common seals are sealant filling or coating; Rubber gasket mechanical fastening seal; Welding (argon arc welding, plasma beam welding) and vacuum nitrogen filling sealing.
From the perspective of sealing effect, the welding sealing is the best, and the amount of filling and coating sealant is poor. For sensors working in clean and dry indoor environment, sensors sealed with glue can be selected, while for some sensors working in humid and dusty environment, sensors with diaphragm hot sleeve seal or diaphragm welding seal and vacuum nitrogen filling should be selected.
(3) In the highly corrosive environment, such as the impact of moisture and acid on the elastomer damage or short circuit of the sensor, the sensor with good corrosion resistance and good tightness should be selected with plastic spraying or stainless steel cover on the outer surface.
(4) The influence of electromagnetic field on the output signal of sensor. In this case, the shielding of the sensor shall be strictly checked to see whether it has good anti electromagnetic ability.
(5) Flammable and explosive not only cause complete damage to the sensor, but also pose a great threat to other equipment and personal safety. Therefore, sensors working in flammable and explosive environments put forward higher requirements for explosion-proof performance: explosion-proof sensors must be selected in flammable and explosive environments. The sealing cover of this sensor should not only consider its tightness, but also considerTo the explosion-proof strength, as well as the waterproof, moisture-proof and explosion-proof of the cable lead-out head.
The selection of sensor range can be determined according to the comprehensive evaluation of factors such as the maximum weighing value of the scale, the number of sensors selected, the self weight of the scale body, the maximum eccentric load and dynamic load that may occur.
Generally speaking, the closer the range of the sensor is to the load allocated to each sensor, the higher the accuracy of its weighing. However, in actual use, because the load added to the sensor is not only the weighed object, but also the dead weight, tare weight, eccentric load, vibration and shock of the scale, many factors should be considered when selecting the sensor range to ensure the safety and service life of the sensor。
According to experience, the sensor should generally work within 30% ~ 70% of its range. However, for some weighing instruments with large impact force in the process of use, such as dynamic track scale, dynamic truck scale, steel scale, etc., when selecting the sensor, it is generally necessary to expand its range, make the sensor work within 20% ~ 30% of its range, and increase the weighing reserve range of the sensor to ensure the sensing

Precautions for use

Precautions for use of load cell

1. Do not exceed the range: frequently exceeding this range will cause irreversible damage to the elastomer and strain gauge inside the symmetrical weight sensor.
2. Use shielded cable, which contains all wires leading to or from the display circuit. The connection and grounding point of shielding wires shall be reasonable. If they are not grounded through the mechanical frame, they shall be grounded externally, but they are not grounded after they are connected with each other, which is floating.
3. Stranded copper wires are used to form electrical bypass to protect them from welding current or lightning stroke.
4. Electrical connections, such as signal cables of sensors, shall not be arranged in parallel with strong current power lines or control lines. If they must be placed in parallel, the distance between them shall be kept above 50cm, and the signal lines shall be sheathed with metal tubes.
5. Try to use structural accessories with automatic positioning (reset) function, such as spherical bearing, articulated bearing, positioning fastener, etc. They can prevent some lateral forces from acting on the sensor.
6. Handle with care, especially the small capacity sensor made of alloy aluminum elastomer. Any impact and drop may cause great damage to its metering performance.
7. Although the weighing module has a certain overload capacity, the overload of the sensor should be prevented during the installation of the weighing system.
8. In any case, the power line and control line shall be twisted to 50 rpm. If the sensor signal line needs to be extended, a special sealed cable junction box shall be used.
9. Horizontal adjustment: horizontal adjustment has two aspects. First, the installation plane of the installation base of a single sensor should be adjusted horizontally with a level gauge. On the other hand, the installation surface of the installation base of multiple sensors should be adjusted to a horizontal plane as much as possible (with a level gauge), especially in the weighing system with more than three sensors.
Cantilever sensors are widely used in small Weighbridge and platform scale. Generally, three sensors or four sensors are used as a group. Through the signal and conditioner, the signals of multiple sensors are processed and then transmitted to the measuring instrument, so as to show the measured values.
10. The signal cable of the sensor shall not be arranged in parallel with the strong current power line or control line (for example, do not put the sensor signal line, strong current power line and control line in the same pipe). If they must be placed in parallel, the distance between them shall be kept above 50cm, and the signal line shall be sheathed with metal pipe.
11. In any case, the power line and control line shall be twisted to 50 rpm. If the sensor signal line needs to be extended, a special sealed cable junction box shall be used. If this kind of junction box is not used, but the cable is directly connected with the cable (soldering end), special attention shall be paid to the sealing and moisture-proof. After connection, the insulation resistance shall be checked and meet the standard(2000 ~ 5000m). If necessary, recalibrate the sensor.
12. If the signal cable is very long and high measurement accuracy should be ensured, the cable compensation circuit with relay amplifier should be considered.
13. All conductors leading to or from the display circuit shall be shielded cables. The connection and grounding point of shielding wire shall be reasonable. If it is not grounded through the mechanical frame, it is grounded externally, but the shielding wires are not grounded after they are connected with each other, which is floating.
Note: three sensors are connected in full parallel. The sensor itself is a 4-wire system, but it is replaced by a 6-wire system in the junction box.
14. The sensor output signal readout circuit shall not be placed in the same box with the equipment that can produce strong interference (such as "controllable silicon", contactor, etc.) and the equipment with considerable heat generation. If this cannot be guaranteed, it shall be considered to set a baffle between them for isolation, and a fan shall be arranged in the box.
15. The electronic circuit used to measure the output signal of the weight sensor shall be equipped with an independent power supply transformer as far as possible, rather than sharing the same main power supply with equipment such as contactors.

How to preliminarily judge the quality of the sensor?
1. Measure resistance
(1) It would be much easier if there were a manual for the load cell. First use a multimeter to measure the input and output resistance of the sensor, and then compare it with the manual. If the difference is large, it means that the load cell should be retested.

(2) If there is no instruction manual, please measure the input resistance, that is, the resistance between exc + and exc -; Output resistance, i.e. the resistance between sig + and sig -; Input resistance, output resistance and bridge resistance shall meet the following relationship:

(3). Input resistance > output resistance > bridge resistance

(4). The bridge resistances are equal or equal to each other
If you have inconsistent measurement results for several times in a row, you can determine that the sensor is damaged.

2. Measure voltage
First, use a multimeter to measure the voltage between the exc + and exc - terminals of the instrument, which is the excitation voltage of the load cell, including DC5V and dc10v. Here, take DC5V as an example. When no-load, use a multimeter to measure MV between sig + and sig - lines. If it is about 1-2mv, it is correct; If the MV number is particularly large, it indicates that the sensor is damaged.
When loading, please use the multimeter MV file to measure the MV number between sig + and sig - wires. It will increase in proportion to the weight of the load. The maximum value is 5V (excitation voltage) * 2mV / V (sensitivity) = about 10mV. Otherwise, it indicates that the sensor has been damaged.

Common problem

Proposal

Name

Tel

QQ

WeChat

Mailbox

Address

Content